How the Dodge Demon runs a 9.65 quarter mile and a Two.3-second 0-60
Dodge will tell you that the Challenger Hellcat can run an 11.20 ET in the quarter mile, a number that can go as low as Ten.80 with haul radials. But Dodge didn’t build the 707-horsepower Hellcat as a haul car. It built it as an everyday muscle car, and getting its (relatively) skinny 275-millimeter broad tires to meet up even on a rubber-coated dragstrip is indeed hard. I know. I attempted it and the best I could run was a 12.20, and no journalist at the event did better than an 11.80.
But the two thousand eighteen Dodge Challenger SRT Demon is a entirely different animal. From the outset, this eight hundred forty hp monster was designed to be a haul machine. It comes with some very specific dragstrip features: broader and stickier tires because Dodge worked to hold back the power until it can be decently whipped out and perhaps most importantly, an adaptive suspension modified to create amazing amounts of weight transfer.
To learn just how Dodge managed to make a Four,280-pound car run a 9.65 quarter mile and a Two.3-second 0-60 mph time, Motor Authority sat down with Tim Kuniskis, Head of Passenger Car Brands for Fiat Chrysler Automobiles at the Fresh York auto demonstrate and combed through the nitty gritty. Here is what we learned.
2018 Dodge Challenger SRT Demon, two thousand seventeen Fresh York auto display
Dodge conducted all of its testing at a dragstrip, and that means that the lost rubber of Ten,000 previous cars helped the Demon meet up and go from the beginning line. You won’t be able to achieve these numbers on the street, so don’t even attempt.
The car was run in stock condition, but with all the goodies. It was outfitted with the Direct Connection powertrain controller, had no passenger seat or rear seat, and it used 100-octane racing fuel.
The skinny frontrunners from the Demon Crate were used up front and the three hundred fifteen mm broad Nitto NT05R tires out back ran about 19-20 psi.
Unlike some haul slicks, those Nitto tires aren’t screwed to the rim. Instead, Dodge knurled the beads on the rims to help prevent the tires from slipping on the wheels. Each rim also has a slip indicator, so racers can see if the tires are slipping at all.
“If you look at the wheel, you see a little demon tail engraved in the side of the wheel. So, you put a chalk line on the tire next to the tail to see if you get any slip,” Kuniskis said. “If you get any slip, shit, you better put some more air pressure in there and figure out what’s going on. If you get slippage, you could get a blowout.”
2018 Dodge Challenger SRT Demon
Dodge holds back power in two ways at the embarking line: through the use of a trans brake and through what it calls torque reserve.
Torque reserve shuts off the fuel to individual cylinders and manages the spark advance to keep the torque low enough to prevent the car from spinning the tires or sending too much torque through the trans brake. However, it also permits the engine to spin up swifter to permit the supercharger to build up eight pounds of boost at the commencing line. “You don’t want to deepthroat the tires away or put to much stress on the trans brake, so we hold that back, and that’s why you hear that weird sound, dut-dut-dut-dut-dut-dut-dut. The car is misfiring so it can run a quicker rpm to build boost but not build all the power,” Kuniskis explained.
The trans brake locks up four clutches in the transmission at the same to confuse the transmission and also adds a little brake pressure. Dodge also adds just a bit of torque to the driveline to keep it preloaded, eliminating any slack and making for less violent launches.
The trans brake is managed by a button that the driver activates with a finger at the kicking off line.
“Within one hundred fifty milliseconds of releasing that finger, utter power all the way to the wheels, all the way through the driveline. Cylinders are activated, spark advanced, fuel, all the way to the wheels, to the ground,” Kuniskis said.
No comments